H-150GF slide valve vacuum pump

Categorize:

New generation slide valve pump series

Single stage slide valve pump series

Summary:

Pumping speed (L/s)H-30GK/42/80/150 limit pressure (Pa. pressure) 0.4 pump speed (rpm)410/410/410/450 motor power (kw)2.2/4/7.5/11 motor speed (rpm)1440 motor model Y100L1-4/Y122M-4/Y132M-4/Y160M-4 pump maximum inlet pressure (Pa)1.3x 10 for long-term operation

Key words:

Vacuum equipment

H-150GF slide valve vacuum pump

Slide valve vacuum pump has a single-stage H type and two-stage 2H type two types of structure.
Two-stage pump than a single-stage pump limit pressure is generally an order of magnitude lower (higher vacuum an order of magnitude).
This type of pump is suitable for pumping in addition to general gas. When a gas ballast valve is used, a gas containing a small amount of condensable vapor, such as water vapor, can also be pumped. When pumping gases that contain too much oxygen, are explosive, corrosive to ferrous metals, and chemically react with vacuum oil, additional devices should be added. This type of pump can be used alone, can also be used as oil diffusion pump, oil vapor jet pump, roots vacuum pump and other high vacuum pump before the pump. This type of pump is widely used in vacuum coating, vacuum heat treatment, vacuum sintering, vacuum metallurgy, vacuum drying, molecular distillation, electronics, solar energy, aviation, aerospace simulation test and other industries.

Characteristic

-Rotary parts are designed according to the point of view of dynamic balance counterweight, so that the pump vibration is small, smooth operation;
-As the moving parts of the pump take small eccentricity, the moment of inertia is small, and the power of the optional motor is also small. For example, H150G with the same pumping speed of 150L/s can be equipped with a 7.5kW motor in the coating industry, while H150 pump needs to be equipped with a 15kW motor;
-The main parts of the pump are optimized and designed with a high degree of generalization, such as slide valves, eccentric wheels, guide rails and pump covers, which can be used for H70G, 2H70G, H150G, 2H120G and other pumps;
-The joint surfaces of the pump body and the pump cover, the oil tank and the oil tank cover are all provided with sealing grooves, which are sealed by O-rings, which are reliable in sealing and convenient in assembly and disassembly, and the old sealing forms of paper pad or resin coating are abandoned;
-The oil and gas separators in the pump are all made of aluminum alloy (except H150), with beautiful appearance, and easy assembly and disassembly when repairing the exhaust valve;
-GA type pump for the bearing outward movement, separated from the pump chamber, separate oil supply, so as to avoid impurities or harmful gases into the bearing, prolong the service life of the bearing;
-GAP type pump for the bearing out and add oil supply pump, forced lubrication, especially suitable for the pump for a long time under the condition of high inlet pressure;
-According to user requirements, it can be equipped with an oil mist eliminator. When the pump works in any state, the exhaust port will eliminate oil fume and create a clean environment.

Main performance parameters Performance Parameter:

Model	ultimate pressure		pumping rate	Intake caliber	Exhaust caliber	with power	Cooling water quantity	Weight
	Pa	Tarr
H-150GF	6.5	5 × 10^-2	100	100	100	11	200	905

Note 1: G in the table indicates the basic type, GA indicates that the bearing moves outward, GAP indicates that the bearing moves outward and the oil pump is forced to supply oil, and GB indicates that the small cylinder sliding rod is replaced by the guide rail assembly.

Note 2: The partial pressure in the table refers to the full pressure indication measured by a thermocouple vacuum gauge, etc.

Note 3: The matching power outside the brackets in the table is the standard configuration, and the matching power inside the brackets is the special configuration.

Note 4: Products marked with "*" in the table are produced according to the drawings of Korea Ucheng Vacuum Company.

H-150GK slide valve vacuum pump

H-150S slide valve vacuum pump

Parameter Copy Introduction Outline drawing Graph

Characteristic

Main performance parameters Performance Parameter:

Model	ultimate pressure		pumping rate	Intake caliber	Exhaust caliber	with power	Cooling water quantity	Weight
	Pa	Tarr
H-150GF	6.5	5 × 10^-2	100	100	100	11	200	905

Note 2: The partial pressure in the table refers to the full pressure indication measured by a thermocouple vacuum gauge, etc.

Note 3: The matching power outside the brackets in the table is the standard configuration, and the matching power inside the brackets is the special configuration.

Note 4: Products marked with "*" in the table are produced according to the drawings of Korea Ucheng Vacuum Company.